Genset Battery Chargers

A genset battery charger is an electronic device that uses AC mains supply to charge the genset's battery. This enables battery to support engine cranking process when required.

SEDEMAC's battery charger product range supports both 12V and 24V batteries and addresses the charging current requirements of 5A and 10A. SEDEMAC's battery chargers are also rugged and field-worthy devices certified to withstand a variety of extreme operating conditions in terms of temperature, vibration, humidity, short-circuit, a wide range of input voltage and so on.

  • The cost effective battery chargers are offered in compact, easy-to-mount packages to enable ready integration in a wide range of genset configurations
  • SEDEMAC's battery chargers adopt a configurable "switch mode power supply" design that helps reduce the energy losses and thereby improve the product life
  • Each product implements both charging modes - constant current and constant voltage and a plethora of diagnostic indicators to ensure trouble-free battery charging in the field

FEATURES

  • Automated three stage battery charging features are provided to ensure longer battery life
  • Advanced switch mode supply design is responsible for higher output efficiency (>85%)
  • Manual boost mode results in fast charging
  • Built-in current and voltage protection circuit which gives effective protection against input over voltage, short circuit, output over current, reverse battery protection, input under-voltage shutdown, etc.
  • 4 LEDs are provided to indicate the operation modes and to diagnose the reverse battery connection
  • Can be used as Switched Mode Power Supply (SMPS) in manual boost mode

PRODUCT COMPARISON

# Feature SEDEMAC
CB1205
ComAp ICHG-120
12-24
Deep Sea DSE 9130 DEIF DBC-1
0 Overall size (mm) 165 x 119 x 67 115 x 111 x 47 136 x 140 x 63 154 x 120 x 79
1 Input voltage range 90-305V 90-305V 90-305V 195-265V
2 Output voltage 13.7V 14.4V 13.7V 13.8V
3 Output current 5A 6A 5A 5A
4 Operating efficiency >85% >90% >80% >80%
5 Operating temperature -30° C to 60° C -30° C to 70° C -25° C to 55° C -25° C to 70° C
6 Boost and float modes Y Y Y Y
7 Protection against faults: short circuit, reverse battery, and more Y Y Y Y
8 Fault alarm indication Y Y Y Y

PRODUCT COMPARISON

# Feature SEDEMAC
CB1210
ComAp ICHG-120
12
Deep Sea DSE
9480 MKII
DEIF DBC-1
0 Overall size (mm) 192 x 129 x 67 114 x 136 x 72 200 x 130 x 70 154 x 120 x 79
1 Input voltage range 90-305V 90-305V 90-305V 195-265V
2 Output voltage 13.7V 14.4V 13.7V 13.8V
3 Output current 10A 10A 10A 10A
4 Operating efficiency >85% >89% >86% >80%
5 Operating temperature -30° C to 60° C -30° C to 70° C -30° C to 55° C -25° C to 70° C
6 Boost and float modes Y Y Y Y
7 Protection against faults: short circuit, reverse battery, and more Y Y Y Y
8 Fault alarm indication Y Y Y Y

FAQs

SPECIFICATIONS

Environmental Specification
  • Operating/Storage Temperature: -30°C to 60°C / -30°C to 85°C, as per IEC 600068-2-1, 2
  • Vibration: 2G in X,Y,Z axis for 8-500 Hz, as per IEC 60068-2-6
  • Humidity:
    Damp Heat (Steady State) Humidity: 95% at temperature: 40°C, as per IEC60068-2-78
    Damp Heat (Cyclic Test) Humidity: 93% at temperature:20°C & 55°C, as per IEC60068-2-30
  • EMI / EMC: Compliance as per IEC 61000-6-2, 4
  • Shock: 15 g for 11 mS, compliance, as per IEC 60068-2-27
Technical Specifications
  • Input Section:
    Input Voltage: 90V to 300V (L-N)
    Frequency: 48Hz to 62Hz
  • Output Section:
    For CB1210:
    Maximum output current: 10A
    Float mode voltage: 13.2V (if charging current < 2A)
    Auto boost mode voltage: 13.7V (if charging current >2A)
    Manual boost mode voltage: 14.4V
    For CB1205:
    Maximum output current: 5A
    Float mode voltage: 13.2V (if charging current < 1A)
    Auto boost mode voltage: 13.7V (if charging current >1A)
    Manual boost mode voltage: 14.4V
  • Efficiency & Regulation:
    Efficiency: > 85%
    Line regulation: <= 1%
    Load regulation: <= 1%
  • Protections:
    Short circuit, DC over voltage, DC over current, Reverse polarity, AC under & over voltage
  • Dimensions:
    CB1210: 192mm x 129mm x 67mm and
    CB1205: 165mm x 119mm x 67mm
  • Weight:
    CB1210:~1.2kg and CB1205:~0.9kg

PRODUCT COMPARISON

Got it!
We use cookies to enhance your experience. By continuing to visit this site you agree to our use of cookies. More info