back

SEDEMAC's new GC2100 is a feature-rich control solution for a wide range of genset engines. Our product offers automation features such as AMF (auto-mains failure), auto exerciser etc. The full HD graphics LCD firmware incorporates useful counters such as mains & genset energy meters, engine run meter and more

  • Built in BTS battery monitoring : Reduces fuel consumption in telecom tower gensets by keeping the genset OFF even when the mains is unavailable by monitoring the 48V battery level
  • BTS battery monitoring and cyclic start/stop modes for low fuel consumption
  • Offers large number of digital /analog inputs and outputs in its class
GC 1200 GC 1200
  • Full graphics backlit LCD with power saving mode
  • Supports Auto (AMF, remote start /stop modes and cyclic mode) and manual modes; monitors 3-ph voltage and frequency for generator and mains; monitors 3-ph load current for generator and mains and power factor for generator
  • Monitors engine safety parameters through both analog resistive and digital switch sensors (e.g - lube oil pressure, engine temperature, fuel level)
  • Controls starter relay, fuel stop relay, alarm hooter and more
  • Supports the battery charging alternator I/O interface
  • Versatile software capable of saving "events" during operation; event log for 100 events with real time clock (RTC) stamps and engine run hour information
  • Deep Sleep Mode is a useful feature to prolong the battery life by suspending the normal functions of the controller
  • Incremental counters for engine starts, engine trips, engine run hour, genset kWh, kVAh, kVArh
  • Measures mains kW, kVA, kWh, kVAh, etc.
  • RS 485 (using MODBUS Protocol) for communicating with other devices
  • Supports parameter configuration at OEM's sites
  • Access to each parameter through PC software or keypad
  • PC connectivity via USB port and RS485
  • Monitoring screens and alarms are available with language options

Environmental Specifications

  • Operating/Storage Temperature: -20°C to 65°C as per IEC 60068-2-1, 2
  • Vibration: 2G in X, Y, Z for 8 Hz-500 Hz as per IEC 60068-2-6
  • Humidity: 0% to 95% RH as per IEC 60068-2-78
  • EMI/EMC: Compliance as per IEC 61000-6-2, 4
  • Power Supply: 8V - 32V DC continuous
  • Ingress Protection: IP65 for front face with optional gasket as per IEC 60529
  • Shock: 15 g for 11 mS, compliance as per IEC 60068-2-27

Technical Specifications

  • Power Consumption: ~0.2 A @ 12V or 24V (standby mode)
  • Crank-start Dropout Survival Period: 50 mS for a drop from 12V
  • Charging Alternator Interface:
    0.25A @ 12V; 0.125A @ 24V
    Diagnostic voltage measurement
  • Digital Output:
    5 x 1A high-side drivers configurable for pre-heat, hooter, etc
    2 x 5A high-side drivers configurable for starter, fuel stop, contactors
  • Digital Input: 9 switch-to-ground inputs configurable for lube oil, temp, fuel level etc.
  • Analog Input:
    5 x resistive inputs (0kΩ-5kΩ); fully configurable for various sources
    2 x 4mA - 20 mA inputs
    1 x differential input (±60V DC) for BTS battery voltage
  • Mains/Genset Voltage Measurement: 20V –385V AC RMS @ 3 Hz – 5 Hz for Ph to N
  • Load Current Measurement: 0A - 5A AC RMS for current transformer (CT) secondary
  • Dimensions:
    External dimensions: 207mm x 160 mm x 38.5 mm
    Mounting panel cut: 189mm x 143 mm